DPC2

Pentium III 6U VME Processor Module



Features

  • 256 MB L2 cache
  • Single-slot VMEbus operation with CompactFlash disk support
  • Supports Intel's EMC-2 Low power module which supports Pentium III with on-die cache
  • SCSI, COM2, PMC I/O are routed out a five-row VME64 P2 connector

 

 

Additional Photos

DPC2 shown with support hardware
(pictured from the left TBPF20BSyS, DPC2, XPC2PTB, XPMC3)


Technical Specifications
Processor Intel's cool running EMC-2 Low Power Module (LPM)
Supports a Pentium III processor and 256 kB on-die L2 cache as well as PCI, AGP, and DRAM interfaces
Single-slot Operation Single-slot VMEbus operation with on-board CompactFlash disk for bootable mass storage
Chipset

High-performance Intel BX chipset (Northbridge is on EMC-2)
Chipset includes DRAM controller, PCI bus arbitration logic and interface, AGP graphics interface, high-performance PCI, IDE interface, RTC, NV-RAM, standard PC timers, Ultra DMA, and interrupt logic

DRAM

Includes 128 MB of surface-mount SDRAM
DIMM module for additional 3.3 V PC100 SDRAM of up to 256 MB
Maximum 384 MB total SDRAM

Additional Memory 2 MB of SRAM, which can be accessed from the VMEbus or the on- board Pentium III without byte-swapping or bus contention issues
Optional 8 MB flash ROM for faster booting of RTOS
VMEbus

Tundra Universe IIB PCI-VMEbus interface provides 64-bit VMEbus transfer rates over 30 MB/sec
FIFOs permit write-posting to maximize available PCI and VMEbus bandwidth
Full Slot 1 (system controller) functions provided
Lower cost versions available without VMEbus

VGA Asiliant's 69030 AGP compatible graphics controller
4 MB of SDRAM is built into the chip
SCSI (optional) Symbios' 53C875 Ultra SCSI controller with transfer rates to 40 B/sec
LAN Intel 82559 single chip Ethernet controller
10BaseT/100BaseTX support, full duplex
IDE Primary Ultra DMA IDE interface with improved transfer rates
PIO and bus master support
Secondary IDE port for CompactFlash on-board booting for flash- based and mechanical storage
Floppy Floppy drive controller, with support for drives up to 2.88 MB
Serial I/O COM1 and COM2 serial ports, based on 16C550 type UARTs with 16- byte transmit and receive FIFOs
Each port can be configured for RS-232 or RS-422/485 independently
Parallel I/O LPT1 parallel port, capable of bidirectional, enhanced parallel port (EPP), and enhanced capabilities port (ECP), per IEEE 1284
BIOS General Software's flash-based system BIOS, upgradeable via floppy
Customized versions can be provided
Watchdog Programmable watchdog timer for system recovery
PMC Expansion One PMC expansion slot available on DPC2
Optional three-PMC carrier supports three PMC cards in two-slot
configuration with the DPC2 (three-slot configuration with Transition Module)
Dynatem offers a broad range of PMC modules includ ing
communication boards, graphics, imaging, DSP and I/O
I/O Interfaces COM1, keyboard/mouse, VGA, 10BaseT/100BaseTX, and PMC, all accessible through front panel
SCSI, COM2, LPT1, PMC I/O, and, optionally, IDE and FDC, routed to the P2 connector (PMC I/O and FDC are on rows d & z)
P2 Breakout Board Rear plug-in module
Routes all P2 I/O to standard connectors
DB-9 connector for COM2, DB-25 connector for LPT1, Ultra- SCSI connector, and floppy drive and IDE connectors
64-pin DIN connector for PMC I/O
Flat-ribbon headers also available for all I/O
Enables interface of all I/O in a single VME slot
Transition Module Requires one additional slot for a two-slot configuration with the DPC2, including floppy and hard drives
Includes front panel SCSI and COM2 connectors
Rugged/Extended Temperature Special thermal design allows extended temperature operation
Tested to -40°/+85°C operation
Use of surface-mount SDRAMs and no socketed components allows high shock/vibration immunity
Power requirements +5 VDC @ 4.4 A typ.
+3 VDC Lithium Coin Cell @ 2.4 mA

Support Hardware
TBP Transition Board Can be offered with two slot wide front panel (in combination with DPC2) or two separate front panels so that it can be separated from DPC2 for embedded environment
· Supports 2.5" IDE hard drive and either CD-ROM or floppy drive
· Transition board which provides SCSI2 connector and COM2 connector (DB9) on front panel
· Two USB ports provided if SCSI is not required
· Other interfaces include LPT1 connector (26-pin dual-row ribbon cable connector), flat panel interface (60-pin dual row header)
· Transition board can be mounted above or below (as pictured) the XPC2 processor board
XPC2PTB Peripheral Transition Board Rear plug-in peripheral transition board with connectors for Ultra SCSI, COM2, and LPT1.
· Floppy and rear I/O interface connectors for PMC cards are included in versions with 5-row P1 and P2 interfaces
· Optional versions without PMC I/O or floppy interface and with three row P1 and P2
· The DPC2 allows routing of IDE to SCSI connector (when SCSI option not used)
XPMC3 PMC Carrier Carrier for 3 PMC cards (requires additional slot)
· Can be provided with single front panel, double-wide front panel (in combination with DPC2) or three-slot wide front panel (in combination with DPC2 and DRC1TB)

Ordering Information
Part# Description
XPC2xxMKx Pentium III CPU board with 500 MHz Pentium III, 10/100Base-TX, SVGA video, 2 COM ports, PMC expansion slot, KB, mouse, bi-directional parallel I/O, single slot, with 128 MB of surface mount SDRAM and 2 MB shared SRAM. Supports CompactFlash. With no SCSI installed. With BIOS installed. Without VMEbus installed.
xPC2Jxxxx 64 MB Flash for DPC2
xPC2Oxxxx 192 MB Flash for DPC2
xPC2Qxxxx 256 MB Flash for DPC2
xPC2Rxxxx 512 MB Flash for DPC2
xPC2Sxxxx 1 GB Flash for DPC2
xPC2Txxxx 2 GB Flash for DPC2
xPC2Uxxxx 4 GB Flash for DPC2
xPC2xFxx Optional 8 MB BootFlash (for booting RTOS kernel)
xPC2xxNx Upgrade to 256 MB (128 MB DIMM module)
xPC2xxOx Upgrade to 384 MB (256 MB DIMM module)
xPC2xxxS With fast/wide SCSI-2 (add to price)
xPC2xxxI Without SCSI-2 but with IDE and floppy routed to backplane
DPC2xxxx With VMEbus (add to price)
Part# Description
Support Hardware
TBPtuuvwyz
Transition board for XPC2 with 40-pin IDE connector, front panel COM port, 26-pin header for printer port, and options as listed below.
Part# Description
Transition Board Options
t = F 1.44 MB floppy drive installed on transition board
t = C CD-ROM drive in place of floppy drive (cannot be used with SCSI)
t = t Neither floppy drive nor CD-ROM drive installed on Transition Board
uu = 20 20 GB IDE hard disk drive installed on transition board
uu = 40 40 GB IDE hard disk drive installed on transition board
uu = uu No IDE hard drive installed
v = T Transition board mounted on top of SBC (socket on bottom)
v = B Transition board mounted on bottom of SBC (socket on top)
v = v Transition board interface via P2 to P2 cabling only, no direct socketed connection (separate single-slot front panels fror SBC and transition board)
w = S SCSI connector (only with SCSI option on XPC2)
w = U USB (not provided with SCSI option)
y = G Gasketed front panel (not available in all configurations)
y = y Non gasketed front panel (default)
z = S Single-slot front panel, can be separated from CPU board
z = D Double-wide front panel for SBC and transition board
XPC2PTB Rear plug-in for XPC2 provides connectors for COM2, LPT1, SCSI (or IDE on XPC2 if SCSI isn't provided on CPU), and a speaker. Floppy connector (for XPC2 only). 64-pin DIN for PMC I/O. Uses 5-row P1 and P2.
XPC2PTBN Rear plug-in peripheral transition board for DPC2 without PMC output or floppy interface. Same as XPC2PTB but without PMC I/O connector and with 3-row P1 and P2
XPMC3 Carrier for 3 PMC cards (requires additional slot). Two slot configuration will provide total of three PMC sites for DPC2, four PMC sites for DMC.
Part# Description
DPC2 Software
DSW-500- DPC VxWorks Tornado BSP (one time charge includes upgrades)
DSW-700-DPC Drive VME, a high performance VME to Windows/NT Systems Software Link (Development version)
DSW-701-DPC Run-time copy of Drive VME
DSW-WINNT Windows NT
DSW-WIN2000 Windows 2000
DSW-800-DPC BSP for Lynx-OS (includes BSP support)
DSW-900-DPC BSP for QNX (includes BSP support)
DSW-A00-DPC BSP for Solaris
DSW-B00-DPC BSP for Linux (includes Redhat operating system)

back to top